Search:

https://www.google.com/search?q=how+to+pronounce+lapua&rlz=1C1GCEA_enES1033ES1033&oq=how+to+rponounce+lapua&gs_lcrp=EgZjaHJvbWUqCwgBEAAYDRgTGIAEMgYIABBFGDkyCwgBEAAYDRgTGIAE0gEJMTI2NzhqMGo3qAIAsAIA&sou...

Found it Lyman 266469 :-)

Thank you

Daniel

Thank you I'll look to find any info on Lyman moulds :-)

Hello , I get a few years ago , a NEI 6.5 /135 grains mould , but I have not any information , anyone know something about it?

Thanks

Daniel

Great info on primers , I have a bit of european info , we have a new primer a extra large primer 6,53 mm Ginex and Murom are now producing then and new .338 Lapua mag cases come with this primer...

Hi Terry , the 9,3x74R it's good caliber for hunting and with enough recoil to pull out the bullet , with paper patch you can't do a roll crimp , you need to stack with two or three punches around...

I have good luck with lyman 311299 sized to .311 sub 2 moa at 100 meters .
G11 have a deep throat and a .300 nose it's not a problem in my rifle
Daniel

I'm in Europe , I can't understand the problem , but I think if the americans don't buy drugs the mexicans maybe pass chile and jalapeños for profit .... IMHO they pass what the americans want....

Hi good article on original loads for the Mosin Nagant in Finnland

http://www.russian-mosin-nagant.com/partisan.htm

DWM

Do a search on youtube

http://www.youtube.com/watch?v=6M1Ghk31WFM

great , thank you to share it.

daniel

Hi Nelson did you get my PM?

Daniel

A friend many years ago when we have no boxer cases for relaod , told me he reloads 308 cases fired in a MN , he uses MN 7,62 x 54 R dies with a Nº2 shell holder , he uses a bit of tape on the...

A good failure , but I have another idea about , FR8 and M96 cock on closing it mean when you close the bolt the firing spring compress , if some "smart" gunsmith touches the trigger sear to have a...

Hi , if someone post how to use the V blok I'll appreciated , I read about this metod but never how to use the block..

Thank you

DWM

Hi tpic402 , it's two or five grooves barrel?

daniel

Hi , a machinist friend made a something like a big gas check , on one side fit the bevel base another side flat to fit in the sizer , no problem and if I need to size flat base bullets I remove it ....

Halo

I'll take one in 316299

Daniel

Load and shot it , if accuracy it's not an issue , you can do it , you have a five grooves or a two grooves bore? if it's a two grooves you have 90% of the land of .303 and 10 percent groove of .312...

A friend offered to cut a new 30'06 chamber this way I'll remove the worst part of the excessive free bore I'll think to do it.

Daniel

Thank you for the replies , I'll try number one first , I re-check measure and in the muzzle it's a bit tight .3024 as a the front part of a 314299 don't fit free , you need to tap it and the nose...

I have a nice argentiean 1909 Mauser action + a stock for it but no barrel , a friend give me two , nice bores , until I check with a borescope , and measure a bit with a lead bullet , barrel nº1...

Cannoner

The P17 have a bore of .300 and groves of .310 try a .313 cast bullet , with five grooves it's not easy to measure .
daniel

Here is the link from bullets points
...

what happen? , not feed from magazine , or not chmaber or not completely close the slide??? my pistol in 9 mm it's an SVI infinity , with fluted chambers ( like and H&K chamber ) and if I have excess...