Do you need/have to use a spring on the powder measure for return? Mine has the linkage that actuates the powder bar.
Do you need/have to use a spring on the powder measure for return? Mine has the linkage that actuates the powder bar.
If you have the failsafe linkage you do not need to use the springs that wrap around the powdermeasure
John J
the failsafe linkage seemed to cause more issues than it was worth.. I prefer the spings on the powder measure personally.. This was on my Dillon 650.. it was one of the first parts I removed when I started loading high volume.
I've never had a single problem with the fail safe system on my 650. What problem(s) have you had?
My 550B has the linkage, I've no issues with it, if the springs were so good why did they get away from them?
ASE master certified engine machinist
Brake & Alignment specialist, ricer to class 8
I have a few dillon measures that still have the springs on them despite the updates with failsafe rods. Not enough difference to be of any concern. Now the failsafe rachet on the 1050 is a different story.
They had problems with 550 owners double charging or not charging their cases. That was pretty common on the net for a while. Also, the springs tend to break after a while, requiring replacement. The fail safe bar is heavier duty.
There may be other reasons, but frankly, I've used both and even with the fail safe, I prefer using the springs.
I can resist this thread no more...
I use the failsafe mechanisms as they are currently designed on ALL my Dillons. They work great. No overcharges, no undercharges. The bar is manually pulled open and manually pulled backward. Most of the clunking and/or clunkiness can be attributed to the "blue nut" being too loose. When PROPERLY adjusted, they are smooth and painless. Why anyone would deliberately disable a safety device that actually works is beyond me.
That said, to each his own. If you have other checks to prevent charging errors, that's all that matters.
Load safe!
Alvarez Kelly;
+1!!
Dale53
+1 more. The springs worked pretty well back in the day, but the linkage while a tiny nuisance
sometimes, is much safer.
Bill
If it was easy, anybody could do it.
I have an older 550 that only has the springs on the powder measures and yes I have doubled charged a few cases. Of course I notice it real quick as a double charge will overflow the case that I am using. (Unique and 2400)
Every one of my double charges are MY FAULT and normally I know it as soon as it happens. I pull the double charged case out, use a can of compressed air to blow the powder out and continue my loading.
I do not use BE powder for volume loading in pistol. The only Rifle round I am set fo is 223 and as of yet - I have not loaded for it on the Dillion.
How many rounds have been loaded on my Dillion since 82? I don't have a clue. But a whole lot of them.
How many double charges made it through the loading process? None. Can't happen with the powders I use.
How many no powder cases made it through the loading process? None to date! (Murphy could visit tomorrow)
FWIW
Big Bore = 45+
Me Too, A Big Plus One.When PROPERLY adjusted, they are smooth and painless. Why anyone would deliberately disable a safety device that actually works is beyond me.
A straight up no ******** reply related to a safety device on a reloader
Regards
John
I never had any trouble with the springs on my 550b powder measure, but one advantage of the linkage is that it is spring loaded at the bottom, and if adjusted correctly, will pull the shell plate up above the primer arm which allows the shell plate to rotate more smoothly in my experience, as well as avoiding the shell plate hanging on a primer in the primer arm when you run out of empty cases and want to finish loading those on the plate.
Ok, I won't use the springs.
ive never had problems with either systems.
Mine are all old style with springs . Works for me . I have almost dbl charged cases except I use powders that fill the cases More than 50% so any dbl charge spills out . I do pistol/revolver and small and large rifle . Once in a while I may run low on powder/primers/cases/boolits and fixed that . Then may forget and just grabed the handel out of mistake an got the order out of sinc so to speak. I know instantly I mess up as I have either not put a case or boolit on or powder is spilling. Primers are next to impossible to miss empty as a buzzer buzzes . I have only had to clean up powder2-3 times in the 80,000 rounds or so I have loaded/reloaded since the late 80s. If I were to buy more new Dillon powder measures I would have to make a choice whether to change over and which way to go. I would NOT have part one , and part another . Had I gotten in and only had the new style I sure in **** would not disable them .
The original system with springs has worked for me since back in the early 80s with no problem. That so called "safety" system on later measures is a contraption solution looking for a problem.
Dan
I have both types and both work fine with one exception.
I use a 30 Carbine funnel (don't remember the letter type) when I load cast boolits in my 7.62x39 cases. With the fail safe linkage installed, the powder will spit out after the funnel is removed from the case causing some spillage. With the spring installed, all of the powder will drop in the case.
The 30 carbine funnel will flare the case of most 30 caliber bottle neck cartridges for loading cast boolits.
When stuffing cast boolits into 308’s, 30-06 and 7.55 Swiss cases, I use the 30 carbine funnel and install a spring in addition to the linkage.
"An armed society is a polite society" R.A. Heinlein 1907 - 1988
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |